Sales Hotline (Press Option 2 then 1) 020 8644 8143 Lines open 8.00 - 13.00/1400 - 17.00 (Mon - Fri)
This long radius bend is used to change the 110mm pipe direction, the spigot end of the bend fits into…
This Ring Seal double socket bend is used to change the 110mm pipe direction at the base of a soil…
This bend is used to change the 110mm pipe direction, the spigot end of the bend fits into the socket…
This bend is used to change the 110mm pipe direction, the spigot end of the bend fits into the…
This slight angled bend is used to change the 110mm pipe direction, the spigot end of the bend fits into…
This Ring Seal double socket 110mm bend can be adjusted by holding both ends and twisting to achieve non-standard angles
This junction is to join a 110mm branch pipe to a 110mm main pipe. It has a spigot outlet that…
Fits into the socket of any 110mm pipe or fitting, it can also be used for the site protection of…
A temporary site cap that is pushed into the end of 110mm plain ended pipe to protect it internally…
Use this to make sure your pipe set up is watertight. Simply fit into the end of your pipe and…
Used to connect rainwater down pipes, surface water and ground floor waste pipes to the drainage system via a ater…
Back inlet (roddable) bottle gully including round 176mm diameter black polypropylene grid. It has a connection at the rear for…
Fits into the rear of the back entry bottle gully. Accepts a 110mm pipe or adaptors for rainwater and waste…
Used when a bottle gully top has to be installed below ground level. The raising piece is 225mm long and…
Square piece of black polypropylene with hole for gully or raising piece, ideal for block or paved areas - not…
Ring seal inlet, spigot outlet, provides a water trap. The invert depth must not exceed 600mm when used below hoppers.…
Ring seal inlet, spigot outlet at 45 degrees, provides a water trap. It can be converted to a "S" trap…
Ring seal back inlet for 110mm pipe. Spigot outlet and a black 148mm square polypropylene grid that rainwater pipes and…
A square hopper with a 140mm spigot end including a black 148mm square polypropylene grid that rainwater down pipes and…
Solvent weld a cut to length piece of pipe into the socket of the hopper and connect to a lowback…
Used when a square hopper top has to be installed below ground level The raising piece is 160mm long and…
Rectangular hopper with 140mm spigot tail, including a rectangular 250mm x 146mm polypropylene grid that rainwater downpipes and ground floor…
Provides at ground level access to the drainage system for cleaning purposes, made from aluminium. Comes complete with plate &…
Provides at ground level access to the drainage system for cleaning purposes. The polypropylene lid is fitted with a seal…
A screw on plug and spigot tail fitting that can be fitted into the socket of a 110mm pipe or…
A bend with a screw on cap on the "heel" that can be removed for access to the drainage system…
This base has the option of up to 3 inlets. 2 blanking plugs are included to blank off unwanted inlets.…
This base has the option to have up to 5 inlets. 3 blanking plugs are included to blank off unwanted…
Used when a shallow access chamber has to be installed so that the top is below ground level. The riser…
Sits on the top of the 320mm diameter access chambers or side riser. Class A: For use in non-vehicular traffic…
Sits on top of the 320mm diameter access chambers or side riser. Class C: For use in non-vehicular traffic areas…
Sits on the top of the 320mm diameter access chambers or side riser. Class A For use in non-vehicular areas)…
Sits on the top of the 320mm diameter access chambers or side riser. Class C: For use in non-vehicular traffic…
Sits on the top of the 320mm diameter access chambers or side riser. Class C: For use in non-vehicular areas,…
Will fit opening of 600mm x 450mm with recess of 46mm. Will accept a multitude of floor finishes such as…
If you have an inspection chamber deeper than 1.2 mt regulations call for the clear opening to be reduced to…
This chamber has the option of up to 5 inlets. 3 blanking plugs are included to blank off unwanted inlets.…
Used when a 460mm diameter chamber has to be installed so that the top is below ground level. The riser…
Sits on top of the 460mm chamber or riser. Class A15 rated for lightly trafficked areas such as domestic gardens…
Finned gasket providing a seal between frame and riser to create sealed system, mitigating the escape of foul odours.
Sits on top of the 460mm chamber or riser. It can be fitted on domestic drives with light vehicular traffic.…